Technical Resources:
Green Pin BigMouth® Towing Shackle BN
Grade 8 towing bow shackle with safety bolt and wider shackle mouth Product details Productcode G-4463
Strength and Weight Table | |||
---|---|---|---|
CERTEX Cat. Ref. No. | Diameter* Inches | Approx. Weight Pounds Per Foot | Nominal Strength Tons |
CX01-0439 | 5/8 | 0.86 | 25.5 |
CX01-0440 | 3/4 | 1.1 | 36.5 |
CX01-0441 | 7/8 | 1.5 | 48.5 |
CX01-0442 | 1 | 2.0 | 62.5 |
CX01-0443 | 1 1/8 | 2.6 | 79.5 |
CX01-0444 | 1 1/4 | 3.2 | 97.6 |
CX01-0445 | 1 3/8 | 3.8 | 118.0 |
CX01-0446 | 1 1/2 | 4.6 | 139.0 |
CX01-0447 | 1 5/8 | 5.3 | 162.0 |
CX01-0448 | 1 3/4 | 6.2 | 185.0 |
*Other sizes available on request
Constructex is recommended as a tubing line where longer service life is desired. Superior abrasion resistance makes Constructex the ideal wire rope for use on scrapyard cranes. Constructex can be recommended with confidence wherever abusive applications exist.
Constructex can be recommended with confidence wherever abrasion and crush resistance are a major concern. In the conventional crane market, this rope has increased life on scrap cranes, clam shell holding and closing lines and boom hoist lines. Constructex also has a long history of superior performance as a tubing line in the well servicing industry. Most recently, Constructex has entered the rotary drill line industry and is outperforming standard 6x19s EIP IRWC RRL lines with up to twice the ton-miles and increased strength. For example, a rig using 1-3/8” Constructex will have a higher rope strength and achieve more ton-miles per foot than a rig using 1-1/2” 6x19s EIP IWRC RRL.
Greater Strength:
The design of Constructex compacts more steel per diameter which provides for higher strength. This allows users to lift heavier loads while maintaining the same rope diameter.
Increased Crush Resistance:
The unique design of Constructex with its reduction of internal voids makes it better to withstand crushing. This makes Constructex the ideal rope for abusive applications.
Longer Rope Life:
The smooth outside surface of Constructex is a direct result of the swaging process. This smooth surface of greatly increased steel area enhances resistance to damage from abrasion.
NOT FOR AIRCRAFT USE. (“Aircraft Cable” has become an accepted industry term for small diameter 7×7 and 7×19 construction wire rope intended for industrial and marine application.) Read important warnings and information.
WARNING: Any warranties, expressed or implied, concerning the use of this product apply only to the nominal strength of new, unused wire rope. All equipment using this product must be properly used and maintained. Wire rope must be properly stored, handled, used and maintained. Most importantly, wire rope must be regularly inspected during use. Damage, abuse or improper maintenance can cause rope failure. Consult the AISI Wire Rope Users Manual, ASME or ANSI Standards, before usage. Wire rope removal criteria are based on the use of steel sheaves. If synthetic sheaves are used, consult the sheave equipment manufacturer. WARNING!
WARNING: Prop 65: Products supplied by CERTEX USA may expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information, visit to www.P65Warnings.ca.gov.
Grade 8 towing bow shackle with safety bolt and wider shackle mouth Product details Productcode G-4463
Dee shackle with square sunken hole screw pin (flush pin) Product details Productcode G-4159 Material bow and pin high tensile steel, Grade 6, quenched and tempered Safety factor MBL equals 6 x WLL Finish hot dipped galvanized Certification 2.1 2.2 3.1 MTCa CE/em>...
Bow shackle with square sunken hole screw pin (flush pin) Product details Productcode G-4169 Material bow and pin high tensile steel, Grade 6, quenched and tempered Safety factor MBL equals 6 x WLL Finish hot dipped galvanized Certification 2.1 2.2 3.1 MTCa CE...
Dee shackle with square headed screw pin Product details Productcode G-4154 Material bow and pin high tensile steel, Grade 6, quenched and tempered Safety factor MBL equals 6 x WLL Finish hot dipped galvanized Certification 2.1 2.2 3.1 MTCa CE Standard EN 13889 and...